Macroinvertebrates

From Sustainability Methods
Revision as of 14:37, 18 April 2023 by Oskarlemke (talk | contribs)
Method categorization for MACROINVERTEBRATES


Method categorization
Quantitative Qualitative
Inductive Deductive
Individual System Global
Past Present Future



In short: Netting, kick sampling and taking benthic cores are methods for collecting macroinvertebrate samples to obtain information about the water quality of a river, lake or pond.

Netting Kick sampling Taking benthic cores
Zone nekton riffles in nekton benthal
Speed of water slow fast-flowing still or slow-moving
Depth of water shallow (pond nets), deep (tow nets) shallow shallow/ deep (using a boat)


Netting

What the method does

Figure 1. Pond net for catching invertebrates. It is important that the collecting bag is long enough to throw it over the brim to prevent invertebrates from escaping. Source: https://www.der-gartenteich.com/teichkescher-klappbar-art.nr.-84296?sPartner=google-de-ts&c=172&gclid=Cj0KCQiA1sucBhDgARIsAFoytUvZORDGHrnxv01LJzM4d4JWxv9RoA5PRK0qP6bboR64KUU2WktN_dgaArTnEALw_wcB

To standardize pond netting to enable comparisons between different sites or different times at the same site, two points in the water are marked with canes and the net is moved in between the poles for a certain number of times at a constant speed. After netting, the net is emptied into a white tray such as a photographic developing tray. The net should be washed very carefully to remove all the specimens. Some specimens such as nymphs often strongly cling to the net. For tow netting, a net is pulled behind a driving boat to estimate the number of zooplankton in open water. While driving the boat, it is important to keep the opening of the net perpendicular to the water surface to keep the opening of the net at the same size throughout each tow. To measure the distance of towing, it is helpful to add a flowmeter to the net. After towing, the content of the collecting bottle is emptied into a container. To wash off all the zooplankton from the inside of the net, water is splashed from the outside. It can take a considerable amount of time to transfer all the invertebrates from the net into the container. The sample is preserved with 95% ethanol.

Strengths and Challenges

Pond nets can be used for quick surveys of the species that occur in a pond or stream. Within only three minutes of netting, you can find 62% of families and 50% of species that you can catch during 18 minutes of netting (Furse et al. 1981). However, this method is hard to standardize as the net-hauls always need to have the same length and the same speed and these are hard to keep up. This means that this method can be used to get an overview on the number of species, but not to compare species richness and abundances between different sites or points in time. Tow nets can be used in deep, open and weed-free waters. They are suitable for large areas of water, especially for watching zooplankton as this is often distributed in patches. They require more work as at least two people are needed, of which one steers the boat and the other one looks after the net. A major problem is to drive the boat with constant speed to standardize the method. Moreover, turbulence caused by the boat might disturb the position of the net. The nets can become clogged by sediment and phytoplankton, so that they lose their catching efficiency.


Kick sampling

What the method does

Figure 2. A student kick-samples a river stretch. Foto: John Rostron. Source: https://upload.wikimedia.org/wikipedia/commons/0/04/Sampling_in_the_River_Roding_-_geograph.org.uk_-_1430581.jpg

Kick sampling is a method that is applied to collect invertebrates from fast-flowing streams, especially from riffles, to assess the water quality. Therefore, a net is held on the ground of the river with its opening facing towards the water flow direction. The substrate is disturbed by kicking and the invertebrates are dislodged and collected in the net a short distance downstream (Figure 2).

The standardized version of this method consists of sampling all the micro-habitats within a stretch of a stream by kick-sampling for a total of three minutes by using a 0.9-mm-mesh pond net. Invertebrates are stored in a white tray. The sample can be preserved with 95% ethanol. After determination of the taxa, individual scores are calculated that are based on the tolerance towards oxygen depletion of each taxon. These scores are summed up to produce a biotic score for this section of the river. This score gives an estimate on the oxygen content of the river stretch and therefore, of its water quality.

Strengths and Challenges

Kick-sampling is a quick and straight-forward method to collect invertebrates from rivers. Moreover, it is standardized and allows to calculate a score that can be used to estimate the water quality. However, only a small proportion of invertebrates from a streambed are caught, so that it cannot be used to calculate population densities.

Taking benthic cores

What the method does

Taking benthic cores is a simple way to collect invertebrates such as polychaete and oligochaete worms (Figure 3). For taking benthic cores, a corer (Figure 4) is sunk into the substrate. If the substrate is firm, the corer is simply pulled from the substrate. If the substrate is soft, a thin piece of metal is slid across the opening of the corer to prevent the sand from falling out. The same method can be conducted in deep water as well, using a boat. In this case, the corer need to be longer and have a bung that fits tightly into its top end. The corer is pushed into the substrate and the bung is pushed into the top end of the corer. This creates a vacuum that prevents the substrate from falling out. The depth of the corer should be around 10 to 15 cm for a sample of 5 cm depth. The corer is then pulled out of the substrate. The benthos is then slowly removed from the corer to not injure the invertebrates. The unwanted part of the sample can be discarded now. Afterwards, invertebrates are extracted by wet sieving with meshes of e.g. the sizes 2 mm, 1 mm and 0.5 mm for invertebrates of down to 1 mm length. To make the sorting process quicker and more efficient, a 1% solution of Rose Bengal dye might be added to stain the translucent invertebrates pink. If the sorting process should take place later on, the sample can be preserved with 95% ethanol.

Strengths and Challenges

In general, this is a relatively quick and easy method to sample benthos. However, sampling in deep water is more challenging as a boat is needed.In this case, the main challenge is to steer the boat into the correct position.

Normativity

Kick sampling underestimates the number of invertebrates attached to stones as these might not let go of the stones and therefore, are not caught in the net. This applies for instance to caddisflies. While taking benthic cores, some larger invertebrates might detect the disturbance in the ground and therefore, retreat deeper into the ground. Other invertebrates such as chironomids might be lost from the corer during sampling (Euliss et al. 1990). In both cases, some taxa get lost from the sample which causes a bias towards other taxa. The taxa that are caught by netting will be strongly determined by the speed of the net. Slow netting causes fast swimming macroinvertebrates to avoid the net whereas fast netting pushes the water in front of the net which also causes some invertebrates to not get caught in the net. Moreover, invertebrate fauna differs with the depth of the water and it might be hard to always keep the net on the same depth during different rounds of netting. This makes catches from nets hard to compare. As netting tends to underestimate benthic invertebrates, it is suggested to combine this method with taking benthic cores.

Outlook

Kick sampling and taking benthic cores can be easily standardized by taking the same number of kicks or cores at different locations. For netting, this is more difficult as the taxa caught in the net strongly depend on the depth of the water and keeping the net at the same height each time can be difficult . All these methods for sampling macroinvertebrates are relatively quick and straight-forward. The time-consuming part is to afterwards sort the individuals into taxa and to determine each individual as far as possible/ needed. At the moment, it is still the standard procedure to determine macroinvertebrates using an identification key and a binocular microscope. However, molecular methods for species determination of macroinvertebrates are recently getting more and more precise. DNA metabarcoding enables species determination based on characteristic DNA sections without sorting the sample into taxa.The advantages are that this method is less time-consuming and enables determination up until species level. It prevents typical mistakes that come from sorting and determining individuals (Baird & Hajibabaei 2020). As experts for certain groups of macroinvertebrates are rare and their work is expensive, meta-barcoding can even help to save money as it is expected to get cheaper in the future (Nichols et al. 2020). Preserving and storing the samples for metabarcoding does not require special treatment. Samples are still suitable for DNA metabarcoding even after one year of storage in 95% ethanol (Stein et al. 2014). Nichols et al. (2020) show that all of the more abundant macroinvertebrate families that were identified by morphological examination were also detected through metabarcoding. However, the authors were unable to assign all macroinvertebrates to species as there is still a great lack of reference DNA barcodes in the DNA barcode libraries. As a result, more individual barcoding is required to fill the gaps in these libraries before metabarcoding is ready to be widely used in practical applications (Nichols et al. 2020).



The author of this entry is Anna-Lena Rau.